https://www.multitechscientificinstruments.in Latest Products Wed, 13 May 2026 17:51:42 +0530 en-us https://www.multitechscientificinstruments.in https://www.multitechscientificinstruments.in/ductility-testing-apparatus.htm https://www.multitechscientificinstruments.in/ductility-testing-apparatus.htm Wed, 21 Jan 2026 00:00:00 +0530 IS 1208-1058, ASTM D 113, IP32, 55, AASHTO T 51 Designed to test three specimens simultaneously. The machine consists of a carriage moving over a lead screw. An electric motor driven reduction gear unit ensures smooth constant speed and continuous operation. The entire assembly is mounted with a stainless steel lined water bath completely encased in metal bound hardwood. It is equipped with an electric pump circulator and heater. The temperature is controlled thermostatically. Two rates of travel i.e. 50 mm/min and 10 mm/min are provided. Suitable for operation on 230 V, 50 Hz, Single Phase, A.C. supply. Complete With: MSI 4025-A Ductility Mould, with Base Plate 3 Nos. MSI 4025-B Thermometer IP 38° C, Range: 23° C to 27° C   https://www.multitechscientificinstruments.in/los-angeles-abrasion-testing-machine.htm https://www.multitechscientificinstruments.in/los-angeles-abrasion-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 LOS ANGELES ABRASION TESTING MACHINE IS 2386 (PART IV) ASTM C 131, AASHTO T-96 Used for testing Crushed Rock, Crushed Slag, Crushed and Uncrushed Gravel For Resistance to Abrasion. Specification: The machine consists of a hollow cylinder mounted horizontally on a study frame on ball bearings. There is an opening which can be closed with a dust tight cover to facilitate charging and discharging the drum with the material under test. A detachable shelf which extends throughout the inside length of the drum which catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated by an electric motor through a heavy reduction gear at a speed of 30-33 R.P.M. A revolution counter is fitted to the frame. A tray is supplied for collection of the material at the end of the test. Complete with Abrasive Charge consisting of a set of Twelve hardened steel balls, approximately https://www.multitechscientificinstruments.in/cement-concrete-testing-equipments.htm https://www.multitechscientificinstruments.in/cement-concrete-testing-equipments.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/soil-test-equipments.htm https://www.multitechscientificinstruments.in/soil-test-equipments.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/bitumen-asphalt-testing-equipments.htm https://www.multitechscientificinstruments.in/bitumen-asphalt-testing-equipments.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/aggregate-testing-equipments.htm https://www.multitechscientificinstruments.in/aggregate-testing-equipments.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/steel-testing-equipments.htm https://www.multitechscientificinstruments.in/steel-testing-equipments.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/jolting-apparatus.htm https://www.multitechscientificinstruments.in/jolting-apparatus.htm Fri, 29 Aug 2025 00:00:00 +0530 The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800 mm from the centre of the table. There is a projecting lug with a plane face on the upper face of the table beneath which is a stop with a rounded upper surface. The table can be raised and allowed to fall freely on the stop by a cam which is connected to a motor and gearbox through a V-belt an pulleys. The cam rotates at a rate of 60 Rev/Min. A stroke counter fitted with micro-switch is provided which stops the machine after 60 Jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surmounted by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Suitable for operation on 230 Volts, Single Phase, A.C. Supply. A Digital Preset Counter can be supplied at an extra cost. Spares and Accessories : (1) Steel mould with base plate having three compartments each having 40 x 40 x 160 mm, internal dimensions. (2) Apparatus for de-moulding the specimen. https://www.multitechscientificinstruments.in/mortar-mixer.htm https://www.multitechscientificinstruments.in/mortar-mixer.htm Fri, 29 Aug 2025 00:00:00 +0530 IS 4031, 1727 & BS 3892 It is used for mixing cement pastes, mortars and pozzolana. Specification: The apparatus consists of an epicyclical type stainless steel paddle imparting both planetary and revolving motion, by means of gears. It has two speeds of 140 + 5 R.P.M. and 285 +10 R.P.M. With planetary motions of approximately 62 R.P.M, +5 R.P.M. and 125 R.P.M. +/- 10 R.P.M. Respectively. The stand of the mixer has arrangement to raise or lower the bowl. Complete with stainless steel bowl of about six liters capacity. Suitable for operation on 230 V, 50 cycles, Single Phase A.C, Supply. https://www.multitechscientificinstruments.in/vibrating-machine.htm https://www.multitechscientificinstruments.in/vibrating-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/compression-testing-machine.htm https://www.multitechscientificinstruments.in/compression-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 516, BS 1881 Specification: In these load frames “C” channels are used, they are welded at the top as well as bottom and with stand high loads. A hydraulic jack is fitted at centre of the base of the load frame, over which can be fitted lower platen and spacer block with the help of centering pin. A lead screw passes through the top of the frame. To the lower end of this lead screw is fixed the upper platen with spherical seat for self alignment. The platens are accurately machined, hardened and polished. The lower platen grooves to correctly place the specimen. Note: The platens are normally rectangular on shape, but no special request square platens or circular platens can be supplied at an extra cost. Ranges: 50 kN to 2000 kN https://www.multitechscientificinstruments.in/semi-automatic-compression-testing-machine.htm https://www.multitechscientificinstruments.in/semi-automatic-compression-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/vibrating-table.htm https://www.multitechscientificinstruments.in/vibrating-table.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/permeability-appartus.htm https://www.multitechscientificinstruments.in/permeability-appartus.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/marshall-stability-test-machine.htm https://www.multitechscientificinstruments.in/marshall-stability-test-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 MSI 4023-A Automatic Marshall Stability Test Machine, 50 KN, 220-240 V 50-60 HZ MSI 4023-B Breaking Head (Stability Mould) 4”1 Pkt.MSI 4023-C Linear Potentiometric, Displacement Transducer, 25x0.001 mm with Bracket for MSI 4023-A and MSI 4023-B MSI 4023-D Indirect Tensile Splitting Device for Compacted Bituminous Samples 100 mm (4") Dia. EN 12697-34, 12697-23, 12967-12, ASTM D1559, D5581, D 6927; AASHTO T245 The 50 kN capacity Automatic Marshall Stability Test Machine is used to determine the maximum load and flow values of bituminous mixtures. The machine comprises of a robust and compact two column frame with adjustable upper cross beam. The unit is a bench mounting compression frame with motor and worm gear housed within the base unit. The speed of the lower platen can be adjusted between 6 mm/min to 60 mm/min using the data acquisition and control unit. For safety, the up and down travel of the lower platen is limited the use of limit switches. Rapid https://www.multitechscientificinstruments.in/pavement-core-drilling-machine.htm https://www.multitechscientificinstruments.in/pavement-core-drilling-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/universal-testing-machine.htm https://www.multitechscientificinstruments.in/universal-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/torsion-testing-machine.htm https://www.multitechscientificinstruments.in/torsion-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/tensile-testing-machines.htm https://www.multitechscientificinstruments.in/tensile-testing-machines.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/flexure-testing-machine.htm https://www.multitechscientificinstruments.in/flexure-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 https://www.multitechscientificinstruments.in/tile-abrasion-testing-machine.htm https://www.multitechscientificinstruments.in/tile-abrasion-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 IS 1237, IS 1706 Specification: This is used for determination of resistance to wear for Cement & Concrete flooring tiles. Tiles specimen of size 7.06 cm x 7.06 cm is pressed face-wise under specific load on a grinding path and abrasive powder is evenly spread on the rotating grinding disc the second parallel side of the tile is subjected to wear for similar number of rotations. The wear of the tile is measured on a thickness gauge specifically made for the purpose. The machine consists of a disc rotating at a speed of 30 R.P.M. in a circular tray. A bracket is provided to hold the specimen. A counter balance lever loads the specimen. Load applied is 30 Kgf. A funnel is fitted to evenly spread abrasive powder on the grinding path. A Pre-set Counter automatically stops the machine after 22 revolutions. This counter is Re-adjustable. The machine works on 440 V A.C. Three Phase electrical supply. On request machine to operate on 230 V A.C. Supply can also be supplied. https://www.multitechscientificinstruments.in/marshall-stability-test-apparatus.htm https://www.multitechscientificinstruments.in/marshall-stability-test-apparatus.htm Fri, 29 Aug 2025 00:00:00 +0530 ASTM: D 1559 T- 62. BS 598-107 Marshall Apparatus Consists Of: Robust construction 50KN capacity Rate of travel 50.8mm/min Safety cut-off switch It consists of body housing, a geared screw jack and motor drive mechanism suitable for operation on 230 V, 50Hz, Single Phase, A.C. supply.   MSI 4022-A MARSHALL LOAD FRAME 1 No. MSI 4022-B Breaking Head Stability Mould, with a dial gauge ( having 25mm travel and 0.01mm least count), for flow measurement 1 No. MSI 4022-C Compaction Mould, Steel cylindrical 3 Nos. MSI 4022-D Base Plate 3 Nos. MSI 4022-E Extension Collar 3 Nos. MSI 4022-F Compaction Pedestal, Manual Operation, Comprising a steel plate capped on a 3 Nos. wooden post. A Mould Clamp is fitted to the top of the plate . MSI 4022-G Compaction Hammer, satisfies BS 598. The hammer has a 4535 g sliding 1 No. weight with a free fall of 457 mm 2 Nos. MSI 4022-H Load Transfer Bar 1 No. MSI 4022-I Paper Discs, Non absorbent, 11 cm diameter pack of 100 No. 1 Pkt. https://www.multitechscientificinstruments.in/.htm https://www.multitechscientificinstruments.in/.htm Fri, 29 Aug 2025 00:00:00 +0530 The California Bearing Ratio Test, (usually called CBR test) is an empirical penetration test for evaluation of mechanical strength of natural ground, subgrades and base courses beneath new carriageway construction. It is to determine the relative bearing ratio and expansion characteristicsThe apparatus confists of  Load Frame, 50kn ( 5000 kgf) Capacity, 3 Speeds  Mould 150mm ID x 175mm high  Perforated Base Plate  Extension Collar, 150mm ID x 50mm high  Penetration Piston, 50mm face dia  Adjustable Bracket, for Penetration Dial Gauge  Circular MetalSpacer Disc. With detachable handle, 148 mm dia x 47.7 mm high time.  Annular MetalWeight, 2.5kg, 147mm dia with 53 mm dia central hole  Perforated MetalWeight 2.5 kg. 147mm dia, with 53mm dia soft  Perforated Plate, 148mm dia, with adjustable stem and lock nut  MetalTripod for Dial Gauge  Cutting Collar  Rammer 2.6kg, 310mm controlled drop  Rammer 4.9kg, 450mm controlled drop  Proving Ring Capacity 50 KN  Dial Gauge, 25 mm travel, 0.01mm least count https://www.multitechscientificinstruments.in/automatic-compression-testing-machine.htm https://www.multitechscientificinstruments.in/automatic-compression-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 $pillar or plate type heavu futy load frame PLC based touch screen controller Pace rate controlled from 1 kn to 10 kn/sec Autoreport generation Auto saving of reports Huge storage capacity of results (10000 Logs) Report download facility through scanner on phon 220 V, AC supply, 50 Hz https://www.multitechscientificinstruments.in/3-rock-bolt-pull-out-test-apparatus.htm https://www.multitechscientificinstruments.in/3-rock-bolt-pull-out-test-apparatus.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 11309, ASTM D 4435 Specification: The objective of the test method is to measure the working and ultimate capacities of rock bolt anchors. The system comprises of a central hole jack, hand pump with a load gauge, directional control value (only for central hole jacks above the capacity of 500 kn), flexible hose pipe 5 mts, truss high tensile bolts with coupling. The pull out force is indicated on the load gauge, however a load cell with digital indicator can be used to measure the pull out load. Arrangement is provided for fixing the dial gauge for estimating deflection against the load Available from 3 ton to 50 ton https://www.multitechscientificinstruments.in/vee-bee-consistometer.htm https://www.multitechscientificinstruments.in/vee-bee-consistometer.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 1199 & BS EN 12350 The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees, which is defined as the time in seconds to complete required vibrating at which the fresh concrete flows out sufficiently to come in contract of the entire face of acrylic disc. Specification: The equipment consists of : A vibrating table size 380 mm long and 260 mm wide, resting upon elastic support at a height of about 305 mm above the floor, complete with Start/Stop switch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescoped with funnel and guide swivel arm is also detachable from the vibrating table. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16 mm dia and 600 mm long rounded at both ends. https://www.multitechscientificinstruments.in/compression-testing-machine-four-pillar-three-pressure-gauge.htm https://www.multitechscientificinstruments.in/compression-testing-machine-four-pillar-three-pressure-gauge.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 516, BS 1881 Specification: The load frame is made up of high quality steel construction with a fixed. Upper lead carrying a ball seated platen. 4 pillars are fixed to the base and the top plate of the loading frame. The upper and lower plates are adjusted with the help of head screw on either side of the pillar. The ram dia of the machine varies from the requirements of the customer. The lower pattern are at the base of the frame above the ram and it is rectangular in shape. Sufficient clearance is provided between the platens to fit in the cylindrical/ cube moulds. Spacer provided to adjust cubes and cylinders. A 20 cm dia pressure gauge with maximum load induction pointer is fitted on the top panel and in turn is connected to the hydraulic pressure pipe. On the right hand a console is fitted within which the electrical motor is fitted along with its coupling which inturn is connected to the pumping unit. A slow / fast loading rate regulator fixed on the top of the console for adjusting the rate of loading. The machine is duly calibrated and passed after inspecting and analyMSIng it with a compression level indicator is provided as a dip stick. https://www.multitechscientificinstruments.in/plate-bearing-test-apparatus.htm https://www.multitechscientificinstruments.in/plate-bearing-test-apparatus.htm Fri, 29 Aug 2025 00:00:00 +0530 Standad Used : IS 1888 1962, ASTM D 1194, BS 13779 This is for estimating the bearing capacity of shallow foundations in situ and for the design of flexible pavement. In the test procedure a steel plate is subjected to gradually increasing load and settlements of the plates recorded. Specification : The out fit consists of 50 tonne hydraulic jack with separate pumping unit fixed to it a 0 - 500KN x 0.5KN. Pressure gauge and flexible metal pipe 5 mtr. long Special ball and socket arrangement Extension rod 12mm dia x 25 cm long Magnetic base with female thread on top for holding extension rod Top end plate, 50mm, dia with male thread for fitting onto the extension rods and positioning the dial gauge plunger Column 15cm dia x 25cm long with flanges complete with four bolts and nuts Column 15cm dia x 50cm long with flanges complete with four bolts and nuts Bridge support of welded steel angle construction, 5 mtr. Span and stands approximately 30 cm. High. Fitted with two quick release clamps a for positioning and holding the dial bracket  https://www.multitechscientificinstruments.in/gyratory-sieve-shaker.htm https://www.multitechscientificinstruments.in/gyratory-sieve-shaker.htm Fri, 29 Aug 2025 00:00:00 +0530 Specification : Carries upto 7 sieves of 150 or 200 mm diameter. The shaker is driven by a 1/4 H.P. Motor through a reduction gear immersed in oil. The sieve table does not rotate but is inclined from the vertical axis and the direction on inclination charges progressively in clockwise direction. If the stop pin below the table is removed, the shaker can have a rotary motion. In addition to this gyratory motion of the table, there is an upward and downward movement ensuring that each square cm of the sieve is utilized. A pair of rods and a holder can be fixed on the top of the upper most sieve, and thus the sieve set in firmly held. Suitable for operation from 230 V 50 Hz, Single phase A.C. supply. a) Adopter for 300 mm dia. sieve available at extra cost b) Adopter for 450 mm dia. sieve available at extra cost  https://www.multitechscientificinstruments.in/wet-sieve-shaker.htm https://www.multitechscientificinstruments.in/wet-sieve-shaker.htm Fri, 29 Aug 2025 00:00:00 +0530 This is yodar type, motor driven sieve shaker for carrying out wet sieve analysis of materials. Specification : Consists of a water reservoir and a holder for sieves, which can take up to 7 sieves of 150mm or 200mm diameter. Shaker is driven by a ¼ H.P. motor through a belt drive. Shaker mechanism moves the sieves up and down in the reservoir. The reservoir has a water out-let for draining out the used water. Suitable for operation 230 V A.C. Single Phase  https://www.multitechscientificinstruments.in/stripping-value-apparatus.htm https://www.multitechscientificinstruments.in/stripping-value-apparatus.htm Fri, 29 Aug 2025 00:00:00 +0530 For determining stripping value of bituminous mixes having aggregate size: 1.0mm to 75 micron. Specification: A circular tray rotates in a vertical plane at a rate of approximately 100 R.P.M. by an electrical geared motor. 4 bottles of approximately 400 cc are mounted on this circular tray at an angle of 900. To each other with their mouth towards center of the tray. A time switch is provided. Suitable for operation on 230 V A.C. Single Phase https://www.multitechscientificinstruments.in/hand-operated-bitumen-extractor.htm https://www.multitechscientificinstruments.in/hand-operated-bitumen-extractor.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : ASTM D2172, AASHTO T-58, T-164. Specification: The Instrument is used for determination and checking of Bitumen percentage in Bituminous mix, the mix is added with a solvent and dissolved bitumen is removed by centrifugal action. Consists of a removable Aluminum rotor bowl, Capacity 1500 gms. With a cap and tightening nut. The bowl assembly is mounted on a vertical shaft, which protrudes from a cast housing. This shaft and thus the bowl is rotated fast manually by enclosed gears in the cast body and handle. Solvent is introduced during the test through the holes in the cap of the housing. A drain is provided to collect dissolved Bitumen coming out of the rotating bowl and getting collected in the housing. https://www.multitechscientificinstruments.in/standard-tar-viscometer.htm https://www.multitechscientificinstruments.in/standard-tar-viscometer.htm Fri, 29 Aug 2025 00:00:00 +0530 Electrical Heating with Immersion Heating Elements and Dimmer stat for controlling the temperature. Suitable for operation on 230 V, 50Hz, Single Phase , A.C. supply. Supplied complete with 10mm cup and valve. https://www.multitechscientificinstruments.in/bitumen-extractor-electrically-operated.htm https://www.multitechscientificinstruments.in/bitumen-extractor-electrically-operated.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : ASTM D2172 AASHTO T-58, T-164 Specification: Centrifuge Extractor, Electrical Operation, Capacity 1500g, with a Dimmer stat for speed control from 2,400 to 3,600 rpm. Suitable for operation on 230 V, 50 Hz, Single Phase, A.C. supply. https://www.multitechscientificinstruments.in/steel-straight-edge.htm https://www.multitechscientificinstruments.in/steel-straight-edge.htm Fri, 29 Aug 2025 00:00:00 +0530 A straight edge approximately 3 meters in length may be used to determine lateral surface regularity of a road surface. This lightweight apparatus is made up of mild steel or aluminum as per customers requirement and is equally supported at both ends producing a set height between the road surface & the beam. Any vertical irregularity is measured using incremented wedges.  https://www.multitechscientificinstruments.in/benkelman-beam.htm https://www.multitechscientificinstruments.in/benkelman-beam.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : AASHTO T 256 Lightweight Aluminium construction Ease of Transportation Unique Telescopic Design Simplifying Field set up  Compact, Thereby reducing the amount of storage space needed Benkelman Beam utilizes the technique of using balanced beam in conjunction with a suitable vehicle to measure road flexure The improved Benkelman Beam is a convenient, accurate device for measuring the deflection of flexible pavements under moving wheel loads. Operating on a simple lever arm principle, the unit consists. Supplied with carrying case Note: Benkelman Beam with Digital Dial Gauge also available at an extra cost  https://www.multitechscientificinstruments.in/automatic-compactor-for-bituminous-mixes.htm https://www.multitechscientificinstruments.in/automatic-compactor-for-bituminous-mixes.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : BS 598-107 Rugged construction to withstand hard work Fully automatic and easy to operate Uniform compaction Automatic Preset Blow Counter Specification: The Automatic Compactor eliminates the laborious process of manual compaction and an even degree of compaction is achieved. The driven mechanism lifts the weight of 4.5kg and drops it through a correct height of 457 mm. The rammer foot is removable, which facilitates preheating. A compaction pedestal with specimen holder is fixed to the base. An Automatic Blow counter enables the number of blows to be present before each test and automatically stops the machine on completion. Suitable for operation on 230 V, 50 Hz, Single Phase, A.C. supply. Note: Also available for modified compaction test  https://www.multitechscientificinstruments.in/thickness-gauge.htm https://www.multitechscientificinstruments.in/thickness-gauge.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 2386 (PART-1) & BS 812 Specification: Used for determining the Flakiness Index of Aggregates. It Consists of a frame with a sliding panel. The Panel has slots of Different Standard Lengths and Widths accurately Cut. https://www.multitechscientificinstruments.in/cylindrical-measures.htm https://www.multitechscientificinstruments.in/cylindrical-measures.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 2386 (PART-III) & BS 812 Specification: It Determines Bulk Density or unit weight of aggregates. It consists of a Calibrated Cylindrical Measures of sheet iron with handles. Capacities available 3, 5, 7, 10, 15, 20 & 30 liters. Complete with One Tamping Rod 16mm dia x 600mm long both ends rounded. https://www.multitechscientificinstruments.in/specific-gravity-and-water-absorption-of-aggregates.htm https://www.multitechscientificinstruments.in/specific-gravity-and-water-absorption-of-aggregates.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 2386 (PART III) & BS 812 The buoyancy balance system consists of a rigid support frame, incorporating a water tank mounted on a platform. A mechanical lifting device is used to raise the water tank through the frame height immersing the specimen suspended below the balance. The balance supplied may also be used as a standard weighing device, thus providing a versatile and comprehensive weighing system in the laboratory Specification: The outfit comprises of Electronic balance, capacity 10 kg. Least Count 0.1gm, provision is made in this balance to suspend density basket under material pan. This balance is mounted on an angle iron frame stand. Density basket. Air tight container to suspend density basket. GI Tray of area not less than 650 cm sq. Absorbent cloths 75cm x 45cm.  https://www.multitechscientificinstruments.in/aggregate-crushing-value-apparatus.htm https://www.multitechscientificinstruments.in/aggregate-crushing-value-apparatus.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 2376 (PART-IV) & BS 812:111 For Measuring of Resistance of Aggregate to Crushing. Specification: The Aggregate Crushing Value (ACV) test set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus are powder coated or galvanized steel, heat treated and ground before manufacturing to make it durable and reliable. Specification: Consists of M.S. Cylindrical Container 150mm +/-0.5mm dia x 130mm to 140mm high with base plate 200 to 230mm/sqr x 6mm thick. A Plunger of 148mm +/-0.5mm dia x 100 to 115mm high. Supplied complete with Tamping Rod, 16mm dia x 600mm long, both ends rounded. Metal Measure 115+/- 0.5mm dia x 180 +/- 0.5mm high. Note: On Special Request Aggregate Crushing Value Apparatus having 75mm dia or 300mm dia cylinder size can be supplied.  https://www.multitechscientificinstruments.in/aggregate-impact-tester-with-blow-counter.htm https://www.multitechscientificinstruments.in/aggregate-impact-tester-with-blow-counter.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 2386 (PART IV) 9377 & BS 812:112 It is robustly designed to determine the aggregate impact value (AIV) of aggregates which provides a relative measure of the resistance of an aggregate to sudden shock or impact. The counter fitted to the machine automatically records the number of blows delivered to the sample, manufactured from heavy duty plated steel to resist corrosion. Specification: The instrument consists of a circular base with Two vertical guides. The Hammer of weight 13.75 +/-0.25kg can be raised to fall freely down the vertical guides. The Height of fall can be adjusted through 380 +/- 5mm. The Hammer is provided with a locking arrangement. The hammer falls freely to the base and is removable for employing. Supplied complete with metal measure 75mm dia x 50mm high (For specimen preparation) and Tamping Rod 230mm long x 10mm diameter. A Blow Counter to count the number of strokes is fitted on top of the equipment. https://www.multitechscientificinstruments.in/dorry-abrasion-testing-machine.htm https://www.multitechscientificinstruments.in/dorry-abrasion-testing-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : BS 812 Used for Testing Aggregates for Resistance to Abrasion. Specification: It consists of a disc rotating about a shaft connected to a reduction gear box coupled to a motor. The disc rotates at 28-30 RPM. Under the rotating disc is a tray with an outlet to facilitate the removal of sand. Two Conical Hoppers are mounted on a bracket fixed to the circular tray. An arrangement is made for start and stop the flow of sand. Two containers with weights are supplied to keep the specimens pressed against the rotating disc. Suitable for operation on 220 V, 50 cycles, A.C. Supply. https://www.multitechscientificinstruments.in/deval-attrition-tester.htm https://www.multitechscientificinstruments.in/deval-attrition-tester.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : ASTM D2-33 & IS 2386 (PART IV)  Used for The Determination of Resistance of Aggregates to Wear by Abrasion. Specification: It consists of two hollow cylinders closed at one end and provided with Fitting covers at the either end. These cylinders are mounted an a shaft at angle of 300 with the axis of rotation of the shaft. The shaft rotates at 30-33 RPM. Through a reduction gear operated by a motor and is provided with a revolution counter. Complete with Abrasive Charge consisting of 12 Nos. Hardened steel Balls of 48mm dia. Suitable for operation on 440 Volts, Three Phase, 50 Cycles, A.C. supply. Note : Option of Digital Preset Counter can be provided at an Extra Cost https://www.multitechscientificinstruments.in/core-cutting-grinding-machine.htm https://www.multitechscientificinstruments.in/core-cutting-grinding-machine.htm Fri, 29 Aug 2025 00:00:00 +0530 Table Mounted Stable Construction Feed arrangement for cutting Feed arrangement for cutting Cooling water arrangement Specification: This unit is designed for cutting and grinding cylindrical rock specimens upto NX size. The outfit includes 200mm dia diamond impregnated cutter, a fine diamond impregnated grinding wheel a water supply system and sampler holder. A V-Vice, to hold the sample up to 55mm dia x 140mm long to be cut parallel and square to the longitudinal axis is provided. Cores longer that 140mm can be prepared by reversing the specimen and holding MSI 6006 against the vice, A hand feed arrangement is provided to facilitate the specimen with a uniform and smooth feeding motions. This unit is provided with a 3 HP, Three Phase, 440 V A.C. Motor. https://www.multitechscientificinstruments.in/point-load-index-tester.htm https://www.multitechscientificinstruments.in/point-load-index-tester.htm Fri, 29 Aug 2025 00:00:00 +0530 Point Load Test Machine is used to determine the strength values of a rock and concrete specimen both in the field and in the laboratory. It consists of a load frame for applying loads up to 100 KN, on which a manual hydraulic jack is mounted. The instrument accepts core specimens up to 102 mm diameter which are loaded by two cone shaped points. A graduated scale indicates the distance between the conical points. The applied load is measured by a pressure. transducer with a digital display unit range 0-100 KN https://www.multitechscientificinstruments.in/bramsilian-test-apparatus.htm https://www.multitechscientificinstruments.in/bramsilian-test-apparatus.htm Fri, 29 Aug 2025 00:00:00 +0530 Standard Used : IS 10082-1982 Specification: The instrument is useful for testing specimen from 50mm dia to 100mm and of thickness of half the diameter. This is to test for indirect measurement of tensile strength of rocks. The specimen is held in circular jaws, this is primarily similar to a compression machine and consists of a small load frame having sturdy base with two vertical threaded rods and an adjustable cross head. The hydraulic jack is fitted at the centre of the base of the load frame. The jack of the load frame is self retracting and two plain platens are supplied. A pressure gauge capacity 0-100 kn x 1 kn is fixed at the base of jack. A maximum pointers is also provided on the gauge, a pair of semi circular platens for 50mm dia samples also provided. The instrument can be used in field also. Optional Extras: Pair of jaws for samples dia (a) 60mm (b) 70mm (c) 80mm (d) 90mm (e) 100mm.